Packaging:
DUREX TROWEL GRADE STUCCO is packaged in 30
kg pails.

DUREX TROWEL GRADE STUCCO is readily available in an assortment of
standard colour schemes. Please refer to our Durex Architectural Coatings
Colour
Selection Guide for more information. Custom colour matching is available
upon request at a slight additional charge.

Coverage:
Average coverage:
13.9-18.6 m²/pail (150-200 ft²/pail)

Application:
DO NOT SUBSTITUTE NOT COMPENSATE DUREX TROWEL GRADE STUCCO WITH WATER OR
OTHER ADDITIVES.

Thoroughly mix DUREX TROWEL GRADE STUCCO in its’ own pail before each use.
Discard all frozen materials, materials which have formed solid lumps at
the bottom of the container and materials which do not appear to be of
homogeneous viscosity. Substrate must be dry, solid and sound, free of
weak and powdery surfaces, free from snow, dew and frost, oil, grease
releasing agents and other deleterious materials detrimental to a positive
bond.

CHECK WITH DURABOND PRODUCTS LIMITED FOR
QUESTIONABLE SURFACES.

Application of the DUREX TROWEL GRADE STUCCO shall be executed by a team
of at least 2 tradesmen. While one tradesman spreads the coating on the
wall the second tradesman following shall float the freshly applied
coating the desired texture.

The process of applying and floating the DUREX TROWEL GRADE STUCCO coating
shall be continuous from the starting point to a natural break point, such
as expansion/control joints and corners.

Using a stainless steel trowel spread the DUREX TROWEL GRADE STUCCO onto
the wall with upward strokes of the trowel. Hold the trowel at a 20-25
degree angle to the wall for better spreadability.

Apply sufficient pressure to provide an even and consistent layer of
coating equivalent to the thickness of the largest sphere-like quartz
aggregate in the mix. Using a plastic trowel begin the flowing process in
the an up and down motion of approximately 400-450mm (16-18 inches) in
stroke length immediately after the coating has been freshly applied. Keep
a wet edge. Do not allow the freshly applied coating to form a surface
with film before beginning the coating process.

The final texture shall be created in the flowing process by the aggregate
rolling between the trowel and the substrate leaving light, semi-circular
scratch-like indentations evenly throughout in the final finish.

Allow a minimum 24 hours for curing. Protect freshly applied coating from
inclement weather until coating has fully set and cured. Prevent rapid
evaporation.


Acrylic High Build Multi-Coloured Decorative Coating

Product Description:
DUREX TROWEL GRADE STUCCO is a high build,
multi-coloured, protective coating consisting of coloured quartz
aggregates embedded in a clear 100% acrylic resin. It is one of the
coatings in the family of Durex Architectural Coatings.

Uses:
DUREX TROWEL GRADE STUCCO is used as an effective long wearing
protective coating over all types of solid substrates. DUREX TROWEL GRADE
STUCCO is mixed to match selected colours. It can be applied as the final
finish coating over all Durex EIF Systems or Durex Lite Coat and/or Durex
Stucco Lite Wall Systems.

Advantages:

  • Excellent durability
  • Excellent water repellence; protects surfaces
    from moisture penetration
  • Breathable coating; allows water vapour within
    the wall assembly to evaporate
  • Excellent adhesion to most common substrates
  • Colourfast; not affected by ultra-violet rays
  Download More Information
 
 

 

 
HTML Editor - Full Version

©2014 Copyright Durabond Products Limited All Rights Reserved Privacy Policy & Terms of Use

Mississauga Office: 6178 Netherhart Road Mississauga, Ontario, Canada L5T 1B7

Western Canada Office: 14345 120th Avenue Edmonton, Alberta, Canada T5L 2R8

Phone: (416) 759-4474 E-mail: info@durabond.com