IBS Equalite Select
Prefabricated 100% Non-Combustible Curtain Wall Panelized System for Facade Enclosures of Mid-Rise and Hi-Rise Buildings

IBS Equalite Select combines all of the features of the Durex® IBS Quantum plus the the feature of being 100% Non-Combustible.  As a prefabricated Curtain Wall System it combines all of the durability essentials of environmental separation controls of heat / air / moisture / fire, strength, durability and aesthetics performance features of the EPS Based Durex IBS Quantum Select plus the fire safety of 100% non-combustible components.  Making it the only fully approved code compliant system in its class.   It brings significant advancements to the conventional, architecturally limited, glass, stone or other material curtain walls through a water-managed, pressure-moderated and energy efficient wall system.

  • Pre-engineered Lightweight Panel Design
  • Totally Non-Combustible Panel System
  • Pressure Moderated Rain Screen Design
  • Air/Water tight Building Envelope Design
  • Geometrically Defined Drainage Cavity (GDDC)
  • Superior Thermal Performance
  • 1 Hour Fire Rated System ULC W-489
  • 2-Hour Fire Rated System ULC W-485
  • Continuous Insulation - (CI) Factor = 0.76 RSI/in

IBS Equalite Select is the only choice when non-combustibility is a must, whether by design and / or code requirements.  It provides the best wall solution in a controlled prefabricated approach that guaranties quality control and speed of construction.  Equally applicable for all types of construction, be it institutional, residential, commercial, industrial and/or temporary.  IBS’s lightweight and flexibility make it an ideal solution for applications in high seismic/wind zones.

Performance Properties
Building Code Conformance


Category 1 CAN/ULC S114

  • Non-Combustible Lamina
  • Non-Combustible Insulation & Structure

Part 3

  • Article
  • Article
  • Article & Table
  • Non-Combustible System
  • Allowable Minor Combustible Components
  • 0-10% Unprotected Openings

Part 4

  • Section 4.1
  • Sub-Section 4.1.3
  • Sub-Section 4.1.4
  • Sub-Section 4.17
  • Structural Load and Procedures
  • Limit State Design
  • Dead Loads
  • Wind Loads

Part 5

  • Section 5.6.1
  • Sub-Section
  • Section 5.9.4
  • Protection from Precipitation
  • Sealing and Drainage
  • Exterior Insulation Finish Systems

Part 9

  • Clause
  • Sub-Section
  • Clause
  • Section 9.27.2
  • Article
  • Sub-Section 9.27.13
  • Article & Table (A)
  • Article
  • Insulation Materials  CAN/ULC S701
  • Position of Low Permeance Membranes
  • General (Cladding, Application)
  • Required Protection from Precipitation
  • Elements of Second Plane of Protection
  • Exterior Insulation Finish Systems
  • 0-10% Unprotected Openings
  • < 0.6 m Limiting Distance


Durex Equalite Select

            Mineral Fiber



Thermal Resistance                GDDC Factor

0.70 RSI  (R 4.0) per inch                  25%


 Air / Vapour Barriers

  Durex Flexseal

Air Barriers

  Durex Flexseal VP

  Durex AirStop


ASTM E96 –Water Vapour Transmission

(Refer to product specific Technical Data Sheet for more detailed data)

Method A                              Method B

                                               2.9 ng/Pa.s.m2


629 ng/Pa.s.m2                              972 ng/Pa.s.m2

185 ng/Pa.s.m2                              505 ng/Pa.s.m2


-Durex“M” fasteners (masonry)

-Durex “W” fasteners (wood)

-Durex “S” fasteners (steel)

-Durex Equalite Washer NC

ASTM B-117 – salt spray

DIN 50012 - SO2 exposure

FM4470  &   DIN 50018 SFW

750 hrs. or better

25+ cycles

30 cycles  Pass

Encapsulated Noncombustible Metal Plate


Impant Resistance

Durex Fiberglass Mesh

(Note: Impact resistance level is directly related to the weight

and  layers of Fiberglass mesh used in the lamina)


ASTM E2486 – Impact Resistance

(Refer to Table 1.5.9 of the IBS Equalite

Select  Specifications for detailed selection

chart for guidance on level of impact

resistance required)

                        Retention            Retention         

                        Physical               Performance

Standard            3 N.m                   10 N.m            PASS

Intermediate    8  N.m                   15 N.m            PASS

High                  13 N.m                   20 N.m            PASS

Ultra High        20 N.m                   30 N.m            PASS

Extreme           25 N.m                   40 N.m            PASS

Base Coat

  Durex Uniplast/Acrybond “S”

  Durex Monobase


CAN/ULC S114  Noncombustibility


Rated Noncombustible

Rated Noncombustible


Durex Architectural  Coatings

   Classic Series

   Premium Series

   Artisan Series

   Kolor Gard Series

   Elastomeric (FX) Series


CAN/ULC S716.1   &

CCMC Report #  13103-R

(Refer to product specific Technical

Data Sheet and CCMC Evaluation

Report # 13103-R for more detailed data)


Durex Architectural Coatings

Meet and exceed all requirements


   Fire Protection

(Refer CCMC Evaluation Report #13103-R

for complete detailed performance data)


(Compliance to NBC (b) )



 (Fire Resistance rated Assemblies)




(Compliance to NBC



Rated as non-combustible cladding ULC design EW21/ EW22


2 hr. FR rating ULC design W425 (Non-Load  Bearing)

1 hr. FR rating ULC design  W489 (Load Bearing)

2 hrs. FR  rating ULC design W485 (Load Bearing)

2 hrs. FR rating ULC design W456 (Non-Load Bearing)


Intertek  listing  # DPL-WEIFS 30-01

Wind Load Resistance

ASTM E330    – sustained


ASTM E330    – cyclic


ASTM E330    – blow-out

-2.5 kPa for 60min. – no visible damage to any of the wall components

-600 cycles alt. 0 to -2.5kPa – no visible damage to any of the wall components

-3.75kPa applied for 10 sec. – no visible damage to any of the wall components - max. pressure 7.12 kPa

Water Tightness


400 Pa pressure difference for 15 min. –  no water penetration through the  exterior surface finish

System Compliance

CCMC Technical Guide for EIFS

CAN/ULC S716.1 EIFS Materials & System

CCMC Evaluation Report # 13103-R

Durex IBS Equalite Select  is fully compliant with:

-CAN/ULC S716.1  Materials & System

-CAN/ULC S716.2 Installation of Components & WRB

-CAN/ULC S716.3 Design Application

System Layer Optional Products Per Layer Notes
Water Resistive Barriers (WRB)
Transition Membranes
Semi Rigid Insulation (Exterior)
Attached with Approved Mechanical Fasteners
Attached with Approved Mechanical Fasteners
Attached with Approved Mechanical Fasteners
Base Coat
Reinforcing Mesh
Finishes - Classic Series
Finishes - Premium Series
Finishes - Artisan Series
Finishes - Flexible Series
Finishes - Kolor Gard