Insulite Select
Advanced Thermal Resistance Drained & Moisture Managed EIFS (Adhered)
Description

Insulite Select is an exterior insulation and finish system consisting of expanded polystyrene insulation with factory-cut channels, insulation adhesive, insulation adhesive, glass fibre reinforcing mesh, base coats, and a finish texture coat which can be selected from any one of the available Durex Architectural Coatings.

Advantages
  • CCMC listed (13103-R)
  • Continuous venting at floor lines and horizontal terminations, using pre-manufactured vented boards
  • Positive drainage (through a network of vertical and horizontal channels)
  • Continuous water resistive barrier
  • Simple interfacing with other pressure equalized claddings
  • 2-hour fire rating in accordance with ULC W-456
  • High Thermal Resistance
  • Aesthetic design flexibility
  • GDDC Factor 25%  (Geometrically Defined Drainage Cavity)
  • CI factor 0.76 RSI (R 4.3) per inch  (Continuous Insulation)
Uses

Insulite Select is suitable for use over a wide range of structurally sound substrates and is recommended for use in buildings which require moisture-managed cladding.

Performance Properties
Building Code Conformance

Classification

Category 1

CAN/ULC S114 & CAN/ULC S101

CAN/ULC S134

 

Non-Combustible Lamina

Fire Test of Exterior Wall Assemblies

Part 3

  • Article 3.1.5.5
  • Article 3.1.5.2
  • Article 3.2.3.7& Table 3.2.3.7
  • Sub-Section 3.2.3.8 (1) (b)
  • Combustible Cladding on Exterior Walls
  • Allowable Minor Combustible Components
  • >10% Unprotected Openings
  • CAN/ULC S101-15 minutes-Non-Combustible Base Coat

Part 5

  • Section 5.6.1
  • Sub-Section 5.6.2.1
  • Section 5.9.4
  • Protection from Precipitation
  • Sealing and Drainage
  • Exterior Insulation Finish Systems

Part 9

  • Clause 9.25.2.2(1)(d)
  • Sub-Section 9.25.5.2
  • Clause 9.27.1.1(5)
  • Section 9.27.2
  • Article 9.27.3.1
  • Sub-Section 9.27.13
  • Article 9.10.14.5 & Table 9.10.14.5 (A)
  • Article 9.10.15.5
  • Insulation Materials  CAN/ULC S701
  • Position of Low Permeance Membranes
  • General (Cladding, Application)
  • Required Protection from Precipitation
  • Elements of Second Plane of Protection
  • Exterior Insulation Finish Systems
  • >10% Unprotected Openings
  • > 0.6 m Limiting Distance
INSULATION

Durex Insulite Select Graphite EPS

CAN/ULC S701

Thermal Resistance                         GDDC Factor

0.76 RSI  (R 4.2) per inch                  25%

WATER RESISTIVE BARRIER

Air / Vapour Barriers

  Durex Green Guard

  Durex Ectoflex

Air Barriers

  Durex Flexcrete

  Durex AirStop

  Durex Dur-A-Mastic 100

  Durex Blue Shield

ASTM E96   – Water Vapour Transmission

 

 

(Refer to product specific Technical

Data Sheet for more detailed data)

Method A                              Method B

11 ng/Pa.s.m2                                 48 ng/Pa.s.m2

18 ng/Pa.s.m2                                  91 ng/Pa.s.m2

 

400 ng/Pa.s.m2                              972 ng/Pa.s.m2

185 ng/Pa.s.m2                              505 ng/Pa.s.m2

248 ng/Pa.s.m2                              645 ng/Pa.s.m2

107 ng/Pa.s.m2                              268 ng/Pa.s.m2

INSULATION ATTACHMENT

Durex Flexcrete

Durex Monobase

Durex VCA 3.0

ASTM D1623    Adhesion Properties

(Refer to product specific Technical

Data Sheet for more detailed data)

1.12 MPa   (162 psi)

1.38 MPa   (200 psi)

1.02 MPa   (148 psi)

LAMINA

Impant Resistance

Durex Fiberglass Mesh

(Note: Impact resistance level is directly related

to the weight and  layers of Fiberglass mesh

used in the lamina)

 

ASTM E2486 – Impact Resistance

 

(Refer to Table 1.5.9 of the Insulite Select

Specifications for detailed selection chart for

guidance on level of impact resistance required)

                        Retention            Retention         

                        Physical               Performance

Standard            3 N.m                   10 N.m            PASS

Intermediate     8  N.m                   15 N.m            PASS

High                  13 N.m                   20 N.m            PASS

Ultra High        20 N.m                   30 N.m            PASS

Extreme           25 N.m                   40 N.m            PASS

Base Coat

Durex Uniplast/Acrybond “S”

Durex Monobase

Durex Flexcrete

CAN/ULC S114  Noncombustibility

Rated Noncombustible

Rated Noncombustible

FINISHES

Durex Architectural  Coatings

   Classic Series

   Premium Series

   Artisan Series

   Kolor Gard Series

   Elastomeric (FX) Series

CAN/ULC S716.1   &

CCMC Report #  13103-R

 

(Refer to product specific Technical

Data Sheet and CCMC Evaluation

Report # 13103-R for more detailed data)

Durex Architectural Coatings

Meet and exceed all requirements

PERFORMANCE

Fire Protection

CAN/ULC S101 & CAN/ULC S114

(Compliance to NBC 3.2.3.8(1) (b))

 

CAN/ULC S101

 (Fire Resistance rated Assemblies)

 

CAN/ULC S134

(Compliance to NBC 3.1.5.5)

Rated as non-combustible cladding ULC design EW21/ EW22

 

 

1 hr. FR rating ULC design  W489 (Load Bearing)

2 hrs. FR  rating ULC design W485 (Load Bearing)

2 hrs. FR rating ULC design W456 (Non-Load Bearing)

Intertek  listing  # DPL-WEIFS 30-01

Wind Load Resistance

ASTM E330    – sustained

ASTM E330    – cyclic

ASTM E330    – blow-out

-2.5 kPa for 60min. – no visible damage to any of the wall components

600 cycles alt. 0 to -2.5kPa – no visible damage to any of the wall components

-3.75kPa applied for 10 sec. – no visible damage to any of the wall components - max. pressure 7.12 kPa

Water Tightness

ASTM E331

400 Pa pressure difference for 15 min. –  no water penetration through the  exterior surface finish

System Compliance

CCMC Technical Guide for EIFS

CAN/ULC S716.1 EIFS Materials & System

CCMC Evaluation Report # 13103-R

Durex Insulite Select is fully compliant with:

    CAN/ULC S716.1  Materials & System

    CAN/ULC S716.2 Installation of Components & WRB

    CAN/ULC S716.3 Design Application

System Layer Optional Products Per Layer Notes
Water Resistive Barriers (WRB)
 
 
 
 
 
 
 
 
Transition Membranes
 
 
 
Insulation Adhesives
 
 
 
 
 
 
Rigid Insulation (Exterior)
 
 
Base Coat
 
 
 
 
 
 
 
Reinforcing Mesh
 
 
 
 
 
Primers
 
 
Finishes - Classic Series
 
 
 
 
 
 
 
 
Finishes - Premium Series
 
 
 
 
 
 
Finishes - Artisan Series
 
 
 
 
 
 
 
 
 
 
 
Finishes - Flexible Series
 
 
 
 
 
 
Finishes - Kolor Gard