Classification

Category 1

CAN/ULC S114 & CAN/ULC S101

CAN/ULC S134

Non-Combustible Lamina

Fire Test of Exterior Wall Assemblies

Part 3

• Article 3.1.5.5
• Article 3.1.5.2
• Clause 3.2.3.7(2) & Table 3.2.3.7
• Article 3.2.3.7 & Table 3.2.3.7
• Sub-Section 3.2.3.8 (1) (b)

• Combustible Cladding on Exterior Walls
• Allowable Minor Combustible Components
• 0-10% Unprotected Openings (with Mineral Fiber)
• >10% Unprotected Openings (with EPS Type I & II)
• CAN/ULC S101-15minutes - Non-Combustible Base Coat

Part 5

• Section 5.6.1
• Sub-Section 5.6.2.1
• Section 5.9.4

• Protection from Precipitation
• Sealing and Drainage
• Exterior Insulation Finish Systems

Part 9

• Clause 9.25.2.2(1)(d)
• Sub-Section 9.25.5.2
• Clause 9.27.1.1(5)
• Section 9.27.2
• Article 9.27.3.1
• Sub-Section 9.27.13
• Article 9.10.14.5 & Table 9.10.14.5 (A)
• Article 9.10.15.5

• Insulation Materials  CAN/ULC S701
• Position of Low Permeance Membranes
• General (Cladding, Application)
• Required Protection from Precipitation
• Elements of Second Plane of Protection
• Exterior Insulation Finish Systems
• >10% Unprotected Openings
• >0.6 m Limiting Distance

Durex Quantum Select Type I

Durex Quantum Select Type II

Durex Equalite Select

CAN/ULC S701

CAN/ULC S702

Thermal Resistance                         GDDC Factor

0.65 RSI  (R 3.9) per inch                  47%

0.70 RSI  (R 4.0) per inch                  47%

0.70 RSI  (R 4.0) per inch                  47%

 Air / Vapour Barriers

  Durex Flexseal

Air Barriers

  Durex Flexseal VP

  Durex AirStop

ASTM E96 –Water Vapour Transmission

(Refer to product specific Technical Data Sheet for more detailed data)

Method A                              Method B

                                               2.9 ng/Pa.s.m²

629 ng/Pa.s.m²                              972 ng/Pa.s.m²

185 ng/Pa.s.m²                              505 ng/Pa.s.m²

-Durex“M” fasteners (masonry)

-Durex “W” fasteners (wood)

-Durex “S” fasteners (steel)

ASTM B-117 – salt spray

DIN 50012 - SO2 exposure

FM4470  &   DIN 50018 SFW

750 hrs. or better

25+ cycles

30 cycles  Pass

Impant Resistance

Durex Fiberglass Mesh

(Note: Impact resistance level is directly related to the weight

and  layers of Fiberglass mesh used in the lamina)

ASTM E2486 – Impact Resistance

(Refer to Table 1.5.9 of the Panelite

Specifications for detailed selection

chart for guidance on level of

impact resistance required)

                        Retention            Retention         

                        Physical               Performance

Standard            3 N.m                   10 N.m            PASS

Intermediate    8  N.m                   15 N.m            PASS

High                  13 N.m                   20 N.m            PASS

Ultra High        20 N.m                   30 N.m            PASS

Extreme           25 N.m                   40 N.m            PASS

Base Coat

  Durex Uniplast/Acrybond “S”

  Durex Monobase

CAN/ULC S114  Noncombustibility

Rated Noncombustible

Rated Noncombustible

Durex Architectural  Coatings

   Classic Series

   Premium Series

   Artisan Series

   Kolor Gard Series

   Elastomeric (FX) Series

CAN/ULC S716.1   &

CCMC Report #  13103-R

(Refer to product specific Technical Data Sheet

and CCMC Evaluation Report # 13103-R for

more detailed data)

Durex Architectural Coatings

Meet and exceed all requirements

   Fire Protection

(Refer CCMC Evaluation Report # 13103-R for

complete detailed performance data)

CAN/ULC S101 & CAN/ULC S114

(Compliance to NBC 3.2.3.8(1) (b) )

CAN/ULC S134

(Compliance to NBC 3.1.5.5)

Rated as non-combustible cladding ULC design EW21/ EW22

Intertek  listing  # DPL-WEIFS 30-01

Wind Load Resistance

ASTM E330    – sustained

ASTM E330    – cyclic

ASTM E330    – blow-out

-2.5 kPa for 60min. – no visible damage to any of the wall components

-600 cycles alt. 0 to -2.5kPa – no visible damage to any of the wall components

-3.75kPa applied for 10 sec. – no visible damage to any of the wall components - max. pressure 7.12 kPa

Water Tightness

ASTM E331

400 Pa pressure difference for 15 min. –  no water penetration through the  exterior surface finish

System Compliance

CCMC Technical Guide for EIFS

CAN/ULC S716.1 EIFS Materials & System

CCMC Evaluation Report # 13103-R

Durex Panelite  is fully compliant with:

-CAN/ULC S716.1  Materials & System

-CAN/ULC S716.2 Installation of Components & WRB

-CAN/ULC S716.3 Design Application