Classification

Category 2 CAN/ULC S134

Fire Test of Exterior Wall Assemblies

Part 3

• Article 3.1.5.5
• Article 3.1.5.2
• Article 3.2.3.7 & Table 3.2.3.7

• Combustible Cladding on Exterior Walls
• Allowable Minor Combustible Components
• >10% Unprotected Openings

Part 5

• Section 5.6.1
• Sub-Section 5.6.2.1
• Section 5.9.4

• Protection from Precipitation
• Sealing and Drainage
• Exterior Insulation Finish Systems

Part 9

• Clause 9.25.2.2(1)(d)
• Sub-Section 9.25.5.2
• Clause 9.27.1.1(5)
• Section 9.27.2
• Article 9.27.3.1
• Sub-Section 9.27.13
• Article 9.10.14.5 & Table 9.10.14.5 (A)
• Article 9.10.15.5

• Insulation Materials  CAN/ULC S701
• Position of Low Permeance Membranes
• General (Cladding, Application)
• Required Protection from Precipitation
• Elements of Second Plane of Protection
• Exterior Insulation Finish Systems
• <10% Unprotected Openings
• <0.6 m Limiting Distance

Durex Flexlite Select Type I

Durex Flexlite Select Type II

ASTM E96   – Water Vapour Transmission

Thermal Resistance                 GDDC Factor

0.65 RSI  (R 3.9) per inch                  15%

0.70 RSI  (R 4.0) per inch                  15%

 Air / Vapour Barriers

  Durex Flexseal

Air Barriers

  Durex Flexseal VP

  Durex AirStop

ASTM E96   – Water Vapour Transmission

(Refer to product specific Technical Data Sheet for

more detailed data)

Method A                              Method B

                                               2.9 ng/Pa.s.m²

629 ng/Pa.s.m²                              972 ng/Pa.s.m²

185 ng/Pa.s.m²                              505 ng/Pa.s.m²

-Durex“M” fasteners (masonry)

-Durex “W” fasteners (wood)

-Durex “S” fasteners (steel)

ASTM B-117 – salt spray

DIN 50012 - SO2 exposure

FM4470  &   DIN 50018 SFW

750 hrs. or better

25+ cycles

30 cycles  Pass

Impant Resistance

Durex Fiberglass Mesh

(Note: Impact resistance level is directly related to the weight

and layers of Fiberglass mesh used in the lamina)

ASTM E2486 – Impact Resistance

(Refer to Table 1.5.9 of the Flexlite Select MF Specifications for

detailed selection chart for guidance on level of impact resistance required)

                     Retention      Retention         

                     Physical        Performance

Standard       3 N.m             10 N.m          PASS

Intermediate 8  N.m            15 N.m          PASS

High               13 N.m           20 N.m          PASS

Ultra High     20 N.m           30 N.m          PASS

Extreme        25 N.m           40 N.m           PASS

Base Coat

    Durex Monobase

    Durex Flexcrete

CAN/ULC S114  Noncombustibility

Rated Noncombustible

Durex Architectural  Coatings

   Classic Series

   Premium Series

   Artisan Series

   Kolor Gard Series

   Elastomeric (FX) Series

CAN/ULC S716.1   &

CCMC Report #  13103-R

(Refer to product specific Technical Data Sheet and CCMC Evaluation Report # 13103-R for more detailed data)

Durex Architectural Coatings

Meet and exceed all requirements

   Fire Protection

(Refer CCMC Evaluation Report # 13103-R  for complete detailed performance data)

CAN/ULC S134

(Compliance to NBC 3.1.5.5)

Intertek  listing  # DPL-WEIFS 30-01

Wind Load Resistance

ASTM E330    – sustained

ASTM E330    – cyclic

ASTM E330    – blow-out

-2.5 kPa for 60min. – no visible damage to any of the wall components

-600 cycles alt. 0 to -2.5kPa – no visible damage to any of the wall components

-3.75kPa applied for 10 sec. – no visible damage to any of the wall components - max. pressure 7.12 kPa

Water Tightness

ASTM E331

400 Pa pressure difference for 15 min. –  no water penetration through the  exterior surface finish

System Compliance

CCMC Technical Guide for EIFS

  CAN/ULC S716.1  EIFS Materials & System

CCMC Evaluation Report # 13103-R

Durex Flexlite Select MF is fully compliant with:

    CAN/ULC S716.1  Materials & System

    CAN/ULC S716.2 Installation of Components & WRB

    CAN/ULC S716.3 Design Application