Insulite Select MF is a pressure moderate, Geometrically Defined Drainage Cavity (GDDC) Exterior Insulation and Finish System that includes a water resistive barrier, or optional air/vapour barrier applied to the substrate to act as a secondary moisture barrier.
- Positive drainage (through a network of vertical and horizontal channels)
- Continous air/vapour barrier
- Simple interfacing with other pressure equlized
- Lightweight
- Economical
- Aethetic design flexibility
Insulite Select MF is suitable for use over a wide range of structurally sound substrates and is recommended for use on buildings where the Building Code allows the use of fire-tested wall assemblies which include combustible foam plastic insulation.
| Building Code Conformance | Classification |
Category 1 CAN/ULC S114 & CAN/ULC S101 CAN/ULC S134 |
Non-Combustible Lamina Fire Test of Exterior Wall Assemblies |
Part 3 |
|
|
|
Part 5 |
|
|
|
Part 9 |
|
|
|
| INSULATION: |
Durex Insulite Select Graphite EPS |
CAN/ULC S701 |
Thermal Resistance GDDC Factor 0.76 RSI (R 4.2) per inch 25% |
| WATER RESISTIVE BARRIER: | Air / Vapour Barriers Durex Flexseal Air Barriers Durex Flexseal VP Durex AirStop |
ASTM E96 – Water Vapour Transmission (Refer to product specific Technical Data Sheet for more detailed data) |
Method A Method B 2.9 ng/Pa.s.m2
629 ng/Pa.s.m2 972 ng/Pa.s.m2 185 ng/Pa.s.m2 505 ng/Pa.s.m2 |
| INSULATION ATTACHMENT: | -Durex“M” fasteners (masonry) -Durex “W” fasteners (wood) -Durex “S” fasteners (steel) |
ASTM B-117 – salt spray DIN 50012 - SO? exposure FM4470 & DIN 50018 SFW |
750 hrs. or better 25+ cycles 30 cycles Pass |
| LAMINA: | Impant Resistance Durex Fiberglass Mesh (Note: Impact resistance level is directly related to the weight and layers of Fiberglass mesh used in the lamina |
ASTM E2486 – Impact Resistance (Refer to Table 1.5.9 of the Insulite Select MF Specifications for detailed selection chart for guidance on level of impact resistance required) |
Retention Retention Physical Performance Standard 3 N.m 10 N.m PASS Intermediate 8 N.m 15 N.m PASS High 13 N.m 20 N.m PASS Ultra High 20 N.m 30 N.m PASS Extreme 25 N.m 40 N.m PASS |
Base Coat Durex Uniplast/Acrybond “S” Durex Monobase Durex Flexcrete |
CAN/ULC S114 Noncombustibility |
Rated Noncombustible Rated Noncombustible
|
|
| FINISHES: | Durex Architectural Coatings Classic Series Premium Series Artisan Series Kolor Gard Series Elastomeric (FX) Series |
CAN/ULC S716.1 & CCMC Report # 13103-R
(Refer to product specific Technical Data Sheet and CCMC Evaluation Report #13103-R for more detailed data) |
Durex Architectural Coatings Meet and exceed all requirements |
| PERFORMANCE: | Fire Protection |
(Refer CCMC Evaluation Report # 13103-R for complete detailed performance data) CAN/ULC S101 & CAN/ULC S114 (Compliance to NBC 3.2.3.8(1) (b) ) CAN/ULC S101 (Fire Resistance rated Assemblies)
CAN/ULC S134 (Compliance to NBC 3.1.5.5) |
Rated as non-combustible cladding ULC design EW21/ EW22
1 hr. FR rating ULC design W489 (Load Bearing) 2 hrs. FR rating ULC design W485 (Load Bearing) 2 hrs. FR rating ULC design W456 (Non-Load Bearing) Intertek listing # DPL-WEIFS 30-01 |
Wind Load Resistance |
ASTM E330 – sustained
ASTM E330 – cyclic
ASTM E330 – blow-out |
-2.5 kPa for 60min. – no visible damage to any of the wall components -600 cycles alt. 0 to -2.5kPa – no visible damage to any of the wall components -3.75kPa applied for 10 sec. – no visible damage to any of the wall components - max. pressure 7.12 kPa |
|
Water Tightness |
ASTM E331 |
400 Pa pressure difference for 15 min. – no water penetration through the exterior surface finish |
|
System Compliance |
CCMC Technical Guide for EIFS CAN/ULC S716.1 EIFS Materials & System |
CCMC Evaluation Report # 13103-R Durex Insulite Select MF is fully compliant with: -CAN/ULC S716.1 Materials & System -CAN/ULC S716.2 Installation of Components & WRB -CAN/ULC S716.3 Design Application |
| System Layer | Optional Products Per Layer | Notes |
|---|---|---|
| Water Resistive Barriers (WRB) | ||
| Transition Membranes | ||
| Rigid Insulation (Exterior) | Attached with Approved Mechanical Fasteners Attached with Approved Mechanical Fasteners Attached with Approved Mechanical Fasteners |
|
| Base Coat | ||
| Reinforcing Mesh | ||
| Primers | ||
| Finishes - Classic Series | ||
| Finishes - Premium Series | ||
| Finishes - Artisan Series | ||
| Finishes - Flexible Series | ||
| Finishes - Kolor Gard |