Quantum Select ICF | Durabond Products Limited

Quantum Select ICF

Continuous Insulation Systems (EIFS)

Quantum Select ICF

Advanced-Drained Moisture-Managed EIFS for ICF (Adhered)

View Project Gallery

System Description

Isometric

Components

Technical Information

Documentation

Description

Quantum ICF is a pressure-moderated, Exterior Insulation and Finish System that includes the installation of Quantum Select over an approved Insulating Concrete Form (ICF) substrate, which is coated with a water-resistive barrier.

Advantages

CAN/ULC S716 compliant
CCMC listed (13103-R)
Continuous venting at floor lines and horizontal terminations, using pre-manufactured vented boards
Positive drainage (through a network of vertical and horizontal channels)
Continuous air/vapour barrier
Simple interfacing with other pressure equalized
2-hour fire rating in accordance with ULC W456
Economical
Aesthetic design flexibility
Continuous Insulation – CI Factor = 0.65 RSI/in (Type 1 EPS) 0.7 RSI/in (Type2 EPS)

Uses

Quantum ICF is intended for use on buildings where the Building Code allows the use of fire-tested wall assemblies which include combustible foam plastic insulation.

1. Water Resistive Barrier (WRB)2. Insulation Adhesive 3. Rigid Insulation (Exterior)4. Base Coat 5. Reinforcing Mesh 6. Primer7. FINISHES Classic Series Premium Series Artisan Series Elastomeric Series Kolor Gard

Performance Properties

Building Code Conformance	Classification	Category 2 CAN/ULC S114 & CAN/ULC S101 CAN/ULC S134	Non-Combustible Lamina Fire Test of Exterior Wall Assemblies
	Part 3	Article 3.1.5.5 Article 3.1.5.2 Article 3.2.3.7 & Table 3.2.3.7 Sub-Section 3.2.3.8 (1) (b)	Combustible Cladding on Exterior Walls Allowable Minor Combustible Components >10% Unprotected Openings CAN/ULC S101-15 minutes - Non-Combustible Base Coat
	Part 5	Section 5.6.1 Sub-Section 5.6.2.1 Section 5.9.4	Protection from Precipitation Sealing and Drainage Exterior Insulation Finish Systems
	Part 9	Clause 9.25.2.2(1)(d) Sub-Section 9.25.5.2 Clause 9.27.1.1(5) Section 9.27.2 Article 9.27.3.1 Sub-Section 9.27.13 Article 9.10.14.5 & Table 9.10.14.5 (A) Article 9.10.15.5	Insulation Materials CAN/ULC S701 Position of Low Permeance Membranes General (Cladding, Application) Required Protection from Precipitation Elements of Second Plane of Protection Exterior Insulation Finish Systems >10% Unprotected Openings >0.6 m Limiting Distance
INSULATION	Durex Quantum Select Type I Durex Quantum Select Type II	CAN/ULC S701	*Thermal Resistance GDDC Factor* 0.65 RSI (R 3.9) per inch 47% 0.70 RSI (R 4.0) per inch 47%
WATER RESISTIVE BARRIER	*Air / Vapour Barriers* - Durex Ectoflex *Air Barriers* - Durex Flexcrete	ASTM E96 – Water Vapour Transmission (Refer to product specific Technical Data Sheet for more detailed data)	*Method A Method B* 18 ng/Pa.s.m²91 ng/Pa.s.m² 400 ng/Pa.s.m²972 ng/Pa.s.m²
INSULATION ADHESIVE	Durex Flexcrete Durex Monobase Durex VCA 3.0	ASTM D1623 Adhesion Properties (Refer to product specific Technical Data Sheet for more detailed data)	1.12 MPa (162 psi) 1.38 MPa (200 psi) 1.02 MPa (148 psi)
LAMINA	Impant Resistance Durex Fiberglass Mesh (Note: Impact resistance level is directly related to the weight and layers of Fiberglass mesh used in the lamina)	ASTM E2486 – Impact Resistance (Refer to Table 1.5.9 of the Quantum Select ICF Specifications for detailed selection chart for guidance on level of impact resistance required)	Retention Retention Physical Performance Standard 3 N.m 10 N.m PASS Intermediate 8 N.m 15 N.m PASS High 13 N.m 20 N.m PASS Ultra High 20 N.m 30 N.m PASS Extreme 25 N.m 40 N.m PASS
	Base Coat Durex Uniplast/Acrybond “S” Durex Monobase Durex Flexcrete	CAN/ULC S114 Noncombustibility	Rated Noncombustible Rated Noncombustible
FINISHES	Durex Architectural Coatings Classic Series Premium Series Artisan Series Kolor Gard Series Elastomeric (FX) Series	CAN/ULC S716.1 & CCMC Report # 13103-R (Refer to product specific Technical Data Sheet and CCMC Evaluation Report # 13103-R for more detailed data)	Durex Architectural Coatings Meet and exceed all requirements
PERFORMANCE	Fire Protection	(Refer CCMC Evaluation Report # 13103-R for complete detailed performance data) CAN/ULC S101 & CAN/ULC S114 (Compliance to NBC 3.2.3.8(1) (b) ) CAN/ULC S134 (Compliance to NBC 3.1.5.5)	Rated as non-combustible cladding ULC design EW23 Intertek listing # DPL-WEIFS 30-01
	Wind Load Resistance	ASTM E330 – sustained ASTM E330 – cyclic ASTM E330 – blow-out	-2.5 kPa for 60min. – no visible damage to any of the wall components -600 cycles alt. 0 to -2.5kPa – no visible damage to any of the wall components -3.75kPa applied for 10 sec. – no visible damage to any of the wall components - max. pressure 7.12 kPa
	Water Tightness	ASTM E331	400 Pa pressure difference for 15 min. – no water penetration through the exterior surface finish
	System Compliance	CCMC Technical Guide for EIFS -CAN/ULC S716.1 EIFS Materials & System	CCMC Evaluation Report # 13103-R Durex Quantum Select ICF is fully compliant with: -CAN/ULC S716.1 Materials & System -CAN/ULC S716.2 Installation of Components & WRB -CAN/ULC S716.3 Design Application

Quantum Select ICF Brochure

Quantum Select ICF Data Sheet

Quantum Select ICF Specifications

Durabond - Colour Selection Guide

System Layer	Optional Products Per Layer	Notes
Water Resistive Barrier (WRB)	AirStop Blue Shield Dur-A-Mastic 100 EctoFlex Flexcrete Flexcrete FS (Fast Set) Green Guard Flexcrete WG (Winter Grade)
Transition Membranes	Barrier Seam Tape EIFS Tape EIFS Tape Superstick TM
Insulation Adhesives	Flexcrete Flexcrete FS (Fast Set) Monobase Monobase Quik-Set VCA 3.0 Insulation Adhesive Flexcrete WG (Winter Grade)
Rigid Insulation (Exterior)	Quantum Select Insulation Board Quantum Select Vent Board Quantum Select Boundary Board
Base Coat	Flexcrete Flexcrete FS (Fast Set) Uniplast / Acrybond Monobase Monobase Quik-Set Flexcrete WG (Winter Grade) Uniplast / Acrybond "S" WInter Grade
Reinforcing Mesh	Standard Mesh Standard Plus Mesh Intermediate Impact Mesh High Impact Mesh Ultra-High Impact Mesh
Primers	Brush Coat Brush Coat Plus
Finishes - Classic Series	Brush Coat Brush Coat Plus Graffiato Marble Coat 1.0 Marble Coat 1.5 Pebble Float Sandex Stucco Spray Venician
Finishes - Premium Series	Century Stone Crystal Coat Gemstone Granite Stonetex
Finishes - Artisan Series	Antico Glaze Rasato Rustico Sandstone Dur-A-Brick Trowel Grade Stucco Pull-Off Aggrex
Finishes - Flexible Series	Graffiato (FX) Marble Coat 1.0 (FX) Marble Coat 1.5 (FX) Pebble Float (FX) Sandex (FX) Venician (FX)
Finishes - Kolor Gard	Kolor Gard Marble Coat 1.0 Kolor Gard Marble Coat 1.5 Kolor Gard Pebble Float Kolor Gard Venician Kolor Gard Graffiato Kolor Gard Brush Coat Kolor Gard Topcoat

Building / Wall Cladding Systems

Protective & Restoration Systems

Seamless Flooring Systems

Search